TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is Electric Tobacconist Coupon really a new pen that was developed by two guys in California. They wished to create a cool writing instrument that appeared as if a genuine pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the market by storm.
The Smok Pen includes a built quality that’s just great. I found that even though it can be an electronic pen the build quality is simply as good as any of the pens that I have reviewed. The reason being of how they made the top cap. You don’t need to worry about the cap cracking or breaking you Smok Valve Pen.
Both biggest differences that separate the Smok Valve from other pens may be the form of the coils and the way that they are built. In general the coil on a Smok Pen is bigger than on other pens. I think that they did this deliberately, to make the pen feel bigger.
If you take a glance at a Smok Pen, you will observe that your body of the pen is round and not smooth like other pens. On the back of the pen there is a little tab that houses the coil. Once you press on the tab you can actually turn the heating element on / off. I must say i liked this feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.
To use the Smok Pen it is advisable to keep carefully the heat button pressed. After the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature you can switch off the heating element. Smok recommends utilizing a 22mm tank. I prefer a more substantial tank, but that’s just me.
Once you put your Smok Pen into the tank you will see a indicator light come on. The indicator light will remain green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen in to the charger before you apply the e-liquids to the coil heads. Additionally it is important to do this before putting your e-liquids into the coil heads.
After you have completed this step, you should always check to see when you are at the right temperature for the coils to fire. Or even then you should turn the energy off and try again. In case you are still not satisfied together with your Smok Pen then I suggest you take it set for some troubleshooting. This is exactly what I would call the “troubleshooting process” because sometimes things just do not work as they should. It is suggested that you perform the following two steps, then go on and check the Smok Pen to see if it still gets the electronic charging port.
Prior to going any further you should remove the battery from your pen and unscrew the magnetic cap. You need to then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. When you have loosened this wire after that you can access the sub-ohm. You need to then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch the coils.
When you have placed the sub-ohm tank in to the pen you should then place the rest of the components including the wattage, the batteries and the heating element into the included microwaveable microwave oven. Start the power and follow the on screen instructions. You need to place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you first put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting does not automatically get set then you should follow the on screen instructions.
Once the Smok Pen has reached the temperature that it requires to reach you should then connect both wires to the negative and positive on the positive post on the Smok unit. You need to then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step would be to connect the positive cable to the bottom of the Smok’s power switch.
After all the components have been placed in to the pen, you should turn the power on. Following the first test run, you have to be able to see the battery life indicator light seriously. If you don’t see any sign of life from the Smok Pen, you need to remove the battery from the pen and then replace it with a brand new one. For your convenience there is also a green light which can be pressed in order to confirm the battery charging status. Once you have done these things and you also do not start to see the green light indicating charging, you should replace the battery.